This great article in the next paragraphs on the subject of A Step-by-Step Guide to Installing a Bathtub is rather insightful. Read on and draw your own conclusions.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't specifically rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is conveniently available, the job can relocate easily; if you need to open a wall to get rid of the old bathtub and also place the new bath tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will require an assistant to move out the old tub as well as set in the new one. Ensure you have actually certified on your own for the work as well as are comfortable trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This write-up will certainly help you install a brand-new bath tub in your bathroom if you have already acquired a brand-new bathtub and also do not need to alter the plan of your previous water pipelines.
Your tools as well as material list ought to comprise the following:
Preparing for the Installation
Firstly, the sustaining frame supplied with the bath must be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic due to the restricted access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the remaining water that will come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Making use of both wooden boards under its feet, put the bathtub in the required position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub up until the level reviews level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the supply of water and also examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has been utilized at the very least once as this will settle it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Safeguard the tap in position with the maker supplied backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, leading to complications with wetness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealer can break relatively early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very eager about A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed my post. In case you liked our blog entry if you please don't forget to share it. Thank you for taking the time to read it.
Best solutions here.